Cooling Tower Packing

What maintenance work is needed for cooling tower fillers during long-term use to ensure its normal operation and

What maintenance work is needed for cooling tower fillers during long-term use to ensure its normal operation and extend its service life?
During the long-term use of cooling tower fillers, the following maintenance work is required to ensure their normal operation and extend their service life:
1. Regular inspection
Appearance inspection: Regularly (at least once a quarter) check the appearance of the filler to observe whether there is damage, deformation, discoloration, scaling, and accumulation of debris on its surface. For example, check whether the corrugated sheet or honeycomb structure of the filler is broken. If there is a break, it may affect the uniform distribution of water and air and reduce the heat exchange efficiency; if there is obvious scale or dirt attached to the surface of the filler, it will hinder heat transfer and need to be dealt with in time.
Structural integrity inspection: Check the overall structural stability of the filler to see if there are problems such as collapse and displacement. Especially for multi-layer fillers, ensure that the connection between the layers is firm and the arrangement is still neat and orderly. If the filler collapses, it will cause water and air to not flow along the normal path, making the local heat exchange effect worse and affecting the heat dissipation performance of the entire cooling tower.
2. Cleaning work
Scale cleaning: Since the circulating water of the cooling tower usually contains certain minerals and other components, the surface of the filler is prone to scaling after long-term operation. A combination of chemical cleaning and physical cleaning can be used. During chemical cleaning, select a suitable descaling agent according to the composition of the scale (for example, for the case of calcium carbonate scale, an acidic descaling agent can be used). After mixing according to the concentration required by the instructions, circulate the descaling agent solution in the cooling tower through a circulating water pump to allow it to fully react with the scale on the surface of the filler, and then rinse it with clean water. For physical cleaning, you can use a high-pressure water gun to rinse the filler to wash away some loose dirt and scale, but pay attention to the intensity and angle of the rinse to avoid damage to the filler.
Debris removal: Clean up leaves, dust, insect corpses and other debris that fall on the filler in time. These debris will block the pores of the filler, affect the circulation of air and water, and thus reduce the heat dissipation efficiency. You can use brushes, rakes and other tools to clean manually. For some hard-to-reach areas, you can also use long-pole tools to assist in cleaning to ensure that the filler pores are unobstructed.
3. Water quality management
Control water hardness: Monitor the water hardness of the cooling tower circulating water and try to control it within a suitable range (generally, the calcium carbonate hardness does not exceed a certain value, and the requirements of different cooling towers are slightly different), because high-hardness water is easy to scale on the surface of the filler, affecting its heat dissipation and normal operation. The scaling tendency of water can be reduced by installing water softening equipment or adding scale inhibitors to reduce the formation of scale on the surface of the filler.
Prevent microbial growth: Microorganisms in water (such as algae, bacteria, fungi, etc.) are easy to multiply in large numbers under suitable temperature and nutrient conditions. They may attach to the filler and form a biofilm, which not only affects heat exchange, but also may corrode the filler material. Appropriate bactericides (such as oxidizing bactericides such as sodium hypochlorite, non-oxidizing bactericides such as isothiazolinone, etc.) can be added to the circulating water regularly, and the content of microorganisms in the water can be monitored to ensure that it is at a low level, keep the filler surface clean, and maintain good heat dissipation performance.
4. Prevent corrosion
Material adaptation environment: According to the specific environment of the cooling tower (such as whether there are corrosive gases, liquids, etc.), select a suitable corrosion-resistant filler material. For example, near chemical plants with acidic gas emissions, it is preferred to use acid-resistant fillers such as fiberglass rather than ordinary plastic fillers that are easily corroded.
Application of anti-corrosion measures: For fillers that have been installed and used, if there is a risk of corrosion, some anti-corrosion measures can be taken, such as applying anti-corrosion paint on the surface of the filler (a paint that is compatible with the filler material and is water-resistant and temperature-resistant must be selected), but it must be ensured that the paint will not have an adverse effect on the heat dissipation performance of the filler and the circulation of water and air; it is also possible to adjust the chemical properties of the circulating water such as the pH value to keep it within the tolerance range of the filler material to reduce the occurrence of corrosion.
5. Repair and Replacement
Local repair: When a small area of ​​damage or deformation is found in the filler, local repair can be performed. For plastic fillers, special plastic welding tools and plastic welding rods of the same material can be used to weld and repair the damaged parts; for fiberglass fillers, resin repair materials can be used. After grinding and cleaning the damaged parts, resin can be applied for repair to restore the integrity of the filler so that it can continue to be used normally.
Overall replacement: If the packing still has serious structural damage and obvious performance degradation after multiple repairs (such as the heat dissipation efficiency is reduced to the extent that it affects the normal operation of the cooling tower, and it cannot be improved after cleaning and other maintenance measures), or it has reached its normal service life (the normal service life of packings of different materials is different, generally 3-5 years for PVC packing, 4-6 years for PP packing, and about 5-8 years for FRP packing, which is greatly affected by the use environment), the packing should be replaced as a whole in time to ensure the stable operation of the cooling tower.
Through the above maintenance work, the normal operation of the cooling tower packing can be effectively guaranteed, so that it can maintain good performance for a long time, thereby extending its service life and ensuring the overall cooling effect and operating efficiency of the cooling tower.